(http://xv4y NULL.radioclub NULL.asia/wp-content/uploads/2013/02/100_3440 NULL.jpg)J’ai continué mes travaux autour de ma mini-station météo avec serveur web. J’ai atteint les objectifs de fonctionnalités que je m’étais fixés, même s’il me reste à enrichir de quelques indicateurs les statistiques. Ensuite il me faudra repasser toutes les valeurs en type float car je les avais mises en entier pour gagner de la place mémoire et parce que l’espace d’affichage sur l’écran LCD était limité. Il me faudra aussi faire un peu de gestion de la cohérence des valeurs pour éviter d’afficher 255°C quand mon capteur distant n’a plus de piles (comme actuellement). A propos du capteur distant, il faudra aussi que je travaille sur son code pour gérer la mise en veille afin d’économiser les batteries. Dernier point important, j’attends toujours mes capteurs de pression atmosphérique (ils sont assez chers donc j’ai hésité à les inclure dans les kits) pour pouvoir gérer ce type de mesures. L’architecture générale étant présente ça ne devrait pas prendre trop de temps à mettre en place.
Vous pouvez donc le voir par vous-même sur ce prototype de mini serveur web météo (http://cairang NULL.radioclub NULL.asia:8080/), cela fonctionne et plutôt bien à mon goût. Ne vous étonnez pas si parfois il y a peu de valeurs affichées car je continue à faire des tests et à remettre à zéro les mémoires…
J’ai même eu ma première commande, car XYL a trouvé cela pratique (pour une fois à propos de mes montages) et en aura besoin d’un pour son café-restaurant. Les services de l’hygiène demande de relever ces valeurs chaque jour en principe, même si dans la réalité peu de monde le fait… Comme elle ne prévoit pas d’ouvrir le service de restauration avant avril, j’ai le temps de mettre tout cela au point.
Je dois encore faire une étude précise, mais je pense pouvoir proposer ces stations météos autour de 70$, le prix variant suivant les options (écran, contrôleur Ethernet, capteur de pression…). Dès que je peux, je mets les informations à jour sur la page produit de la boutique (http://xv4y NULL.radioclub NULL.asia/boutique/?slug=product_info NULL.php&products_id=31). Les composants sont en fait assez chers si on veut une précision correcte (les capteurs DHT-11 par exemple ne sont bons que pour des mesures relatives) et il y a deux micro-contrôleurs (un pour la station et un pour le capteur distant). Dans tous les cas ça ne sera pas avant mi-mars prochain car les approvisionnements vont être bloqués pour plusieurs semaines à partir du week-end prochain avec le nouvel an lunaire.
En attendant je partage avec vous le code source du premier programme de test que j’avais fait pour mon prototype de mini station météo web (http://xv4y NULL.radioclub NULL.asia/2013/02/01/mini-station-meteo-web/). Il a évolué depuis mais celui-ci en principe fonctionne et offre le service de base… Il est prévu pour un Arduino Nano (ATMega328) et se compile avec Arduino 1.0.1. Je vous conseille d’utiliser mes packages librairies (http://xv4y NULL.radioclub NULL.asia/boutique/docs/) pour pouvoir les compiler.
/* Arduino Thermometer and Humidity mini web server using internal and remote DHT11 sensors By Yannick DEVOS - XV4Y http://xv4y.radioclub.asia/ Copyright 2013 Yannick DEVOS under GPL 3.0 license Any commercial use or inclusion in a kit is subject to author approval ==== This program sense and displays the current temperature and relative humidity for a local and remote sensors It serve the values to a mini web server thanks to an ENC28J60 Ethernet module In order to compile this program with Arduino 1.0.1, you will need to install 3 libraries : - DHT-sensor Library by Adafruit https://github.com/adafruit/DHT-sensor-library - VirtualWire Library by Mike McCauley http://www.open.com.au/mikem/arduino/VirtualWire.pdf - Ethercard Library by JeeLabs http://jeelabs.net/pub/docs/ethercard/index.html ==== Revision history : v1.00 2013-02-02 First release with mini web server test ==== This program needs at least 2KB of SRAM, that means an ATMega328... The DHT11 Sensor need to be connected as described here below - Connect pin 1 (on the left) of the sensor to +5V - Connect pin 2 of the sensor to whatever your DHTPIN is (here pin D12) - Connect pin 4 (on the right) of the sensor to GROUND - Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor We also need a push button on pin D2. For RF modules, please see the VirtualWire documentation ==== This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You can download a copy of the GNU General Public License at <http://www.gnu.org/licenses/> */ #include <EtherCard.h> #include "DHT.h" #include <VirtualWire.h> // Here some parameters you would like to edit #define RXPIN A1 // What pin we use for Remote Sensor RX module #define BAUDRATE 2000 // Transmission speed in bps, 1000-2000 is ok a give similar ranges, higher is useless #define RX_LOST 60 // Max time in seconds without the sensor is considered lost #define DHTPIN A2 // What pin we have connected the DHT sensor #define DHTTYPE DHT22 // ethernet interface ip address static byte myip[] = { 192,168,1,100 }; // gateway ip address static byte gwip[] = { 192,168,1,254 }; // ethernet mac address - must be unique on your network static byte mymac[] = { 0x74,0x69,0x69,0x2D,0x30,0x31 }; const byte header[4] = {0x01,'D','H','T'}; // Here you should not be touching it const char http_OK[] PROGMEM = "HTTP/1.0 200 OK\r\n" "Content-Type: text/html\r\n" "Pragma: no-cache\r\n\r\n"; const char http_Found[] PROGMEM = "HTTP/1.0 302 Found\r\n" "Location: /\r\n\r\n"; const char http_Unauthorized[] PROGMEM = "HTTP/1.0 401 Unauthorized\r\n" "Content-Type: text/html\r\n\r\n" "<h1>401 Unauthorized</h1>"; DHT dht(DHTPIN, DHTTYPE); byte Ethernet::buffer[700]; // tcp/ip send and receive buffer BufferFiller bfill; int hi=0xFF, ti=0xFF, hr=0xFF, tr=0xFF; int last_rx; unsigned int counter=0; float tf=1; byte buf[VW_MAX_MESSAGE_LEN]; byte buflen = VW_MAX_MESSAGE_LEN; void setup(){ ether.begin(sizeof Ethernet::buffer, mymac); // Start the Ethernet module ether.staticSetup(myip, gwip); vw_set_rx_pin(RXPIN); vw_setup(BAUDRATE); vw_rx_start(); // Start the RF receiver PLL running } void loop() { hi = int(dht.readHumidity()); // we convert to integer since the DHT11 has not enough precision anyway ti = int(dht.readTemperature()); if (vw_have_message()) { // If we have a message from the RF module if (vw_get_message(buf, &buflen) && !memcmp(&buf, &header,4)) // If it is checked and the header is the same { // First temp, the RF module send a float but we only display an integer memcpy(&tf, &buf[4], 4); tr = int(tf); // THen humidity memcpy(&tf, &buf[8], 4); hr = int(tf); last_rx = millis()/1000; // We save when was the last data received } } if ((millis()/1000) > (last_rx+RX_LOST)) { // Without signal from the sensor for more than RX_LOST seconds, the sensor is considered out of reach hr = 0xFF; tr = 0xFF; } // wait for an incoming TCP packet, but ignore its contents word len = ether.packetReceive(); word pos = ether.packetLoop(len); if (pos) { delay(1); bfill = ether.tcpOffset(); char *data = (char *) Ethernet::buffer + pos; if (strncmp("GET /", data, 5) != 0) { // Unsupported HTTP request // 304 or 501 response would be more appropriate bfill.emit_p(http_Unauthorized); } else { data += 5; if (data[0] == ' ') { // Return home page homePage(); counter++; } else { // Page not found bfill.emit_p(http_Unauthorized); } } ether.httpServerReply(bfill.position()); // send http response } } void homePage() { bfill.emit_p(PSTR("$F" "<meta http-equiv='refresh' content='5'/>" "<title>Mini web météo v1.0 XV4Y</title>" "<h1>Le temps du delta du mékong chez <a href=\"http://xv4y.radioclub.asia\">XV4Y</a></h1>" "<h2>Capteur interne</h2>" "Temp : $D°C</br>" "Hum. : $D%</br>" "<h2>Capteur distant</h2>" "Temp : $D°C</br>" "Hum. : $D%" "<h6>$Dème connexion.</h6>" "<h5>Copyright(C)2013 - <a href=\"http://xv4y.radioclub.asia/\">Yannick DEVOS XV4Y</a></h5>" ), http_OK, ti, hi, tr, hr, counter); }
Voici aussi le code pour le capteur distant. Il fonctionne lui sur un MSP430G2452 et est écrit avec Energia 009.
/* Remote Temperature/Humidity sensor for MSP430G2452 * Code for Energia 009 * By Yannick DEVOS - XV4Y - December 2012 http://xv4y.radioclub.asia/ Copyright 2012-2013 Yannick DEVOS under GPL 3.0 license Any commercial use or inclusion in a kit is subject to author approval ==== * Run on MSP430G2452 * Hook a DHT sensor module to pin P2_1 * Hook a 433MHz TX module to P2_4 * Several pins are available for LED debugging ==== Revision history : v1.00 2012-12-18 First release, without MCU power saving features ==== This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You can download a copy of the GNU General Public License at <http://www.gnu.org/licenses/> */ #include "DHT.h" #include <VirtualWire.h> #define DHTTYPE DHT11 #define DHTPIN P2_1 // DATA Pin pour le DHT #define TXPIN P2_4 // DATA Pin pour le module TX RF #define BAUDRATE 2000 // Transmission speed in bps, 1000-2000 is ok a give similar ranges, higher is useless #define PWRPIN P1_6 // Pin to turn ON/OFF power to the modules #define LEDERR P1_0 // This LED will turn on when DHT is not ok float h, t; byte trame[12] = {0x01,'D','H','T',0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF}; // The frame to be transmitted with "DHT" as header DHT dht(DHTPIN, DHTTYPE); void setup() { pinMode(PWRPIN, OUTPUT); pinMode(LEDERR, OUTPUT); vw_set_tx_pin(TXPIN); vw_setup(BAUDRATE); dht.begin(); } void loop() { digitalWrite(PWRPIN, HIGH); // Apply power to the modules delay (1000); // We have to wait 1 second to let the DHT sensor stabilize // Reading temperature or humidity takes about 250 milliseconds! // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor) t = dht.readTemperature(); h = dht.readHumidity(); // Check if returns are valid, if they are both 0 then something went wrong! if (t == 0 && h == 0) { digitalWrite(LEDERR, HIGH); } else { // First temperature memcpy(&trame[4], &t, 4); // Then humidity memcpy(&trame[8], &h, 4); vw_send((byte *)trame, 12); digitalWrite(LEDERR, LOW); } vw_wait_tx(); // Wait until the whole message is gone digitalWrite(PWRPIN, LOW); // We turn off power to save batteries delay(5000); // We rest 5 seconds before the next reading, longer wait time will save more batteries... }